How to take apart Ninja blender to clean: A complete guide

How to take apart Ninja blender to clean? It’s a very common question from Ninja Blender users. The Ninja Blender is a powerful and versatile kitchen appliance that can handle a wide range of blending tasks. However, after extended use, it’s common for the blender to accumulate gunk and residue in hard-to-reach places. That’s why, disassembling your Ninja blender is crucial for more thorough cleaning.

In this article, I will show you how to take apart and clean the Ninja blender properly.

Safety Precautions

Before you begin the cleaning and disassembling process, it’s important to prioritize safety. Follow these safety precautions to minimize the risk of accidents and ensure a smooth cleaning experience:

  • Before starting the cleaning process unplug the Ninja Blender from the power source.
  • Allow the blender to cool down completely to avoid any burns.
  • Wear protective gloves to prevent any injuries while handling sharp blades.
  • Work in a well-lit area to ensure visibility and prevent accidental damage.
  • Keep children and pets away from the cleaning area for their safety.
  • Refer to the manufacturer’s instructions and user manual for model-specific guidelines.

By following these safety precautions, you can proceed with confidence to clean and disassemble your Ninja Blender.

Step-01: Disassembling the Lid and Gasket

The lid and gasket of the Ninja Blender create a tight seal to prevent any leaks or spills during blending. Here’s how you can disassemble and clean the lid and gasket:

  • Remove the lid from the blender pitcher according to the manufacturer’s instructions. This may involve releasing clips, latches, or a twist-lock mechanism.
  • Once the lid is removed, locate the gasket on the underside of the lid.
  • Lift the gasket out of its groove gently. Be careful not to damage or stretch the gasket during the removal process.
  • Clean the lid and gasket by washing them with warm water and mild dish soap. Use a soft brush or sponge to remove any residue or debris.
  • Rinse the lid and gasket thoroughly with clean water to remove any soap residue.
  • Dry the lid and gasket completely before reassembling them with the blender pitcher.

Visit here for ensure more Thorough cleaning your ninja blender rubber gasket.

Step-02: Removing the Blade Assembly

The blade assembly is a critical component of the Ninja Blender that requires proper cleaning. Here’s how you can remove and clean the blade assembly:

  • Unplug the blender and remove the pitcher.
  • Locate the blade assembly at the bottom of the pitcher. It is usually held in place by a screw-on mechanism.
  • Use a screwdriver to unscrew the blade assembly in a counterclockwise direction. Be careful not to apply excessive force.
  • Once the blade assembly is unscrewed, lift it out of the pitcher. Handle it with care as the blades may be sharp.
  • Clean the blade assembly by washing it with warm water and mild dish soap. Use a soft brush or toothbrush to remove any residue or debris.
  • Rinse the blade assembly thoroughly with clean water to remove any soap residue.
  • Dry the blade assembly completely before reassembling it with the pitcher.

To remove tough stains from the blade, you should deep clean your Ninja Blades.

Step-03: Taking Apart the Base Unit

The base unit of the Ninja Blender houses the motor and other internal components. Cleaning the base unit is crucial to maintain optimal performance. Here’s how you can disassemble and clean the base unit:

  • Locate any screws or fasteners on the bottom or back of the base unit.
  • Use a screwdriver to carefully remove these screws. Keep track of them for reassembly later.
  • Lift or separate the base unit to expose the internal components. Take note of the arrangement of the components for easier reassembly.
  • Clean the base unit and internal components using a soft brush or cloth. Be cautious around any electrical connections and delicate parts.
  • Remove any dust or debris that may have accumulated inside the base unit.
  • Inspect the components for any signs of damage or wear. Replace any damaged parts if necessary.
  • Reassemble the base unit by placing the components back in their original positions. Ensure that all wires are properly connected and the screws are tightened securely.

Cleaning the base unit regularly will ensure that your Ninja Blender operates at its best and prolong its lifespan.

How do you clean your Ninja self-cleaning?

The Ninja self-cleaning feature is designed to simplify the cleaning process. To clean your Ninja Blender with its self-cleaning setting, fill the pitcher with warm water. Then add a few drops of mild dish soap there. Select the self-cleaning setting and let the self-cleaning cycle run for about 30-60 seconds.

Once the cleaning cycle is complete, empty the soapy water. And rinse the pitcher thoroughly with clean water. Then, allow it to air dry.

The self-cleaning feature not only saves time but also ensures that your Ninja blender is always ready for the next use. Just a few simple steps and your blender will be clean and fresh.

How do you clean the inside of a Ninja blender handle?

Cleaning the inside of the blender handle can be a bit tricky. Follow these simple steps to achieve a spotless blender handle:

  1. Before cleaning, make sure the blender is unplugged to avoid any accidents.
  2. Gently detach the handle from the pitcher or main body of the blender, depending on the model you own.
  3. Use a soft sponge or cloth soaked in warm, soapy water to wipe the inside of the handle thoroughly.
  4. Rinse the handle with clean water to remove any soap residue. Then, dry it with a clean towel.
  5. Once the handle is completely dry, reattach it to the blender pitcher or main body.

By following these easy steps, you can ensure that your Ninja blender handle remains clean.

Reassembling Your Ninja Blender

After disassembling and cleaning the individual components of your Ninja Blender, it’s time to reassemble them for future use. Here’s a step-by-step guide to reassembling your Ninja Blender:


If you disassembled the base unit, gently place the components back in their original positions first. Make sure all wires are properly connected, and the screws or fasteners are tightened securely.

Then, attach the blade assembly back onto the bottom of the blender pitcher. And Place the pitcher back onto the base unit. Make sure it is aligned properly. Place the gasket back into the groove on the underside of the lid.

After all, perform a visual check to ensure that all components are securely in place.

How do you get stains out of a Ninja Blender

Over time, the jar can develop tough stains and odors that can affect the overall cleanliness of your blender. Vinegar and Baking soda are excellent cleaning agents that can help remove tough stains and odors from the blender jar. Here’s how you get stains out of a Ninja Blender:

Make a paste by mixing vinegar and baking soda. Apply the paste to the stained areas of the blender jar. Allow the paste to sit for a few minutes, or even overnight for tougher stains. After that, rinse the jar thoroughly to remove the paste and any remaining stains.

By following these methods, you can remove stains from your Ninja blender jar looking it clean and fresh.

How do you get mold out of your Ninja blender

Discovering mold in your blender can be concerning.

To eradicate mold, prepare a mixture of equal parts white vinegar and water. Use this natural solution to scrub away the mold from the affected areas. The acidic properties of vinegar effectively combat mold.

For stubborn mold stains, create a paste with baking soda and water. Apply it to the affected areas and let it sit for a few minutes before scrubbing with a soft brush or sponge.

After removing the mold, rinse all blender parts with warm water. Let the components air dry completely before reassembling the blender.

Regularly inspecting and cleaning your blender will prevent mold growth. It will also ensure that your appliance remains in top-notch condition and provides healthy, mold-free blends.

Note: Before tackling the mold issue, always unplug the blender to avoid electrical mishaps. Take apart all removable parts, such as the pitcher, lid, and rubber gasket. This will ensure a clean and safe blending experience.

How Do You Unscrew a Ninja Blender?

Unscrewing the base of a Ninja blender can be perplexing. Especially when it seems stuck. But fear not, we’ve got you covered with these straightforward steps:

  • Before attempting to unscrew the blender, ensure it is unplugged for safety.
  • Place a non-slip kitchen mat or a thick towel on your counter. This will provide a stable base and prevent any accidental slips.
  • Using both hands, grip the base of the blender securely. Twist counterclockwise to unscrew it. It might require some force, but be patient and steady.
  • If the base remains stubborn, try using a hairdryer to apply gentle heat to the area. The heat can help loosen any tight seals or residues.
  • Wrap a rubber band around the base for extra grip. This can improve your traction and make unscrewing easier.
  • If all else fails, think about contacting the manufacturer’s customer support. You can take the blender to an authorized service center for assistance.

With these techniques, you can effortlessly unscrew your Ninja blender.


Regularly cleaning your Ninja Blender is essential to maintain its performance, hygiene, and longevity. By following the steps provided in this article, you can disassemble your blender properly. Which will ease your cleaning process. Don’t forget to prioritize safety and inspect your blender regularly for any signs of wear or damage. With a clean and properly maintained Ninja Blender, you can enjoy smooth and delicious blends for years to come.

Frequently Asked Questions

Can Ninja Blender base get wet?

No, the Ninja Blender base should not get wet. It contains electrical components and should never be submerged in water or any other liquid. To clean the base, simply wipe it with a damp cloth, ensuring no water enters the motor or electrical parts.

What are the black specks in my Ninja Blender?

The black specks in your Ninja Blender may be caused by mineral deposits or mold growth. It is essential to regularly clean and maintain your blender to prevent the accumulation of residue and potential mold formation.

What is the black stuff on the bottom of my blender?

The black stuff on the bottom of your blender is likely a combination of food particles, oils, and minerals that have accumulated over time. Regularly clean all components of your blender to keep it in pristine condition.

Can baking soda clean the blender?

Yes, baking soda can effectively clean your blender. Create a cleaning solution by mixing water with a teaspoon of baking soda and blend it for a few seconds. Then, rinse thoroughly with water to remove any residue.

How long do Ninja blenders usually last?

With proper care and maintenance, Ninja blenders can last for several years. The longevity of your blender depends on how well you clean it, handle it, and replace any worn-out parts when necessary.

What can you not put in a Ninja blender?

Avoid blending hot liquids in a Ninja blender, as the pressure from steam can cause the contents to splatter and lead to burns. Additionally, do not blend hard objects like bones or ice cubes without following the manufacturer’s guidelines.

Can you just brush off mold?

No, you should never try to brush off mold from your blender. Mold can be harmful to your health. If you discover any, it’s best to disassemble the blender and clean all components thoroughly with a mixture of water and vinegar or use mild dish soap. If the mold persists, it’s safer to replace the affected parts.

Leave a Comment